GM Sniper 2 Update: throwing some paint and starting work on the base

It’s been awhile since I last updated on this project. We got new Kampfer shirts in, so the last update was used to promote that. Somewhere in the middle of this post there will be some shameless plugging for our new Kampfer shirts as well as our reprinted Shiki shirts. But enough of that; on with the update. Starting off, I felt that the red bit for the crotch needed a slight bit of detail so I took the scriber and cut some plastic on the sides. It’s relatively simple plastic removal but does a decent job of adding some detail.

Returning to the rear skirts; in the last update, I had just started putting together a scratch built knife and was creating a sheath for it. I trimmed down that plastic piece from the GM Spartan conversion kit and sanded it down to fit into the existing spot on the rear skirt. I also had to sand down some of the internal area for the rear skirt piece for the damn thing to fit. Once the piece fit; I drilled into the plastic and glued a magnet into place. I drilled a corresponding spot on the knife’s guard and added a magnet there. Now the knife is actually held by the power of the magnet instead of friction or just gluing it into place. I wanted the knife functional. A little priming shows areas to fix.

(more…)

Continue ReadingGM Sniper 2 Update: throwing some paint and starting work on the base

GM Sniper 2: priming and resin casting

I was originally going to post this progress update on Monday; but since we had just gotten back from Tatsu Hobby’s contest; I wanted that post to stand on its own. So a few days later, I’ve continued to plug away at the kit as I got some new ideas flowing but still need to finish off the old ideas that I’ve already started. I also finalized the work on the new toe and will show the process of making resin copies. Since a majority of the build work is done; I also took some time and sprayed the initial layer of primer over the legs and other parts. At this point, it is about 90% primed. Here’s a quick teaser picture.

More after the jump.

(more…)

Continue ReadingGM Sniper 2: priming and resin casting

Back to work on the RGM-79SP-2

Finally getting back to work on this project. Taking a two week vacation really breaks the momentum I had going for this kit. I actually thought about bringing pieces of the thing with me to work on while I was in Tokyo and Hong Kong. Then, knowing my damn luck, I would have lost said pieces. So I just quit cold turkey and left everything here. Plus, I really didn’t have time to do any sort of model building while I was gone. Hell, I even got to catch up through the first half of Iron Blooded Orphans by marathoning it on my flight back as my attempt to reset my biological clock and fix the potential week long jet lag. It worked, I only ended up taking an hour long nap before landing back in LAX. Ok, enough digression. My trip to Tokyo and HK was quite fruitful. I ended up picking up a bunch of new tools that I immediately put into use. While in Hong Kong, I visited the Man 66 Hobby shop on the 7th floor of the Richmond Commercial Building in Mong Kok. I saw a damn cool cutting tool, “the Chopper II” which is an improvement on “the Chopper” that I had picked up a couple of months ago. So my first order of business when I got back was to order this via Amazon. It is pretty damn difficult to get back into building mode. So it took a few days. I didn’t quite know where to start; or actually, I wasn’t motivated enough to actually start. But over the last week, I started slow on a few pieces here and there. The majority of the work for this post is focused on the legs. We’ll start off with where I last left off.

So the last update on the project, I had cut up the outer calf parts. The problem is that the cut isn’t precise. So after sanding an opening, I needed to glue some plastic back into place to rebuild some of the screwed up areas. So this past week, I’ve been slowly adding more plastic, sanding it down, test fitting, then adding more plastic back, and resanding, etc. I also glued the two halves back together so that I have a solid connection on the ends. It seems counter intuitive to cut the part in half only to glue it back together, but it makes for a much easier process for this kind of a mod. The last picture in this series shows what it currently looks like. There is still some cleanup work; but I’m progressing. I also added some strips of styrene to the back of the thruster housing. I still need to sand and prep that bit of detail.

Continued after the jump!

(more…)

Continue ReadingBack to work on the RGM-79SP-2

MG GM Sniper 2 Progress: Front skirts, new antenna, and some chest mods

This is going to be a fairly sizable update. This includes the work from last week as well as over the weekend. I’m starting to focus and get more and more work done as the inspiration continues. The front skirts are REALLY plain looking. Yes, it’s a grunt suit, so it should be relatively simplistic cannon fodder that all GMs aspire to be; but it’s just plastic, so what’s better than cutting the plastic and then gluing more plastic to the cut plastic? There are still some scattered bits of work here and there as is typical with this kind of build. While glue or putty is drying, the focus on other sections keeps the work going. All the while, I’m taking pictures of all the progress.

Full details of the work and pictures after the jump!

(more…)

Continue ReadingMG GM Sniper 2 Progress: Front skirts, new antenna, and some chest mods